送料机尾料夹夹料长度一般长度是多少mm

很荣幸能为你解答！
夹式送料机操作说明书耐锐送料机热1已有 12 次阅读 2012-08-05 16:32 标签: 送料机

夹式送料机的用途
GS-906N简易操作顺序及说明

1． 材料线设定： 送料机夹式送料机

固定座置放材料，手动阀On (No1)夹住材料，材料下缘与模具同高或略高0-01mm
2送料时间设定
冲床：355°，送料机：送料至0（按冲床运转方向，转动皮带轮，把副尺移却至本尺0对齐）。
3调整料厚： 送料机夹式送料机

A．送料机之设定：手动阀Off(No2),料厚指示环向左旋转旋紧之0为0
B人工调整：（1）移动座于上死点（0°），手动阀On（No1）,材料松紧之间，向左旋005mm并固定之。
（2）固定座于上死点（180°）不放松，手动阀On（No1）,材料松紧之间，向左旋005mm并固定之。
4送距调整：
A冲床时间：90°（送料终点。 送料机夹式送料机

B松开M16螺母，以T型扳手调整至所需尺寸，并固定M16螺母。注：送距不稳定时，请留意送距调整螺丝固定环是否松动。
5放松点设定：
A时机：送料完成后，遵梢定位于材料。 送料机夹式送料机

B松开放松凸轮之M8螺丝，调整放松线使其对准放松点，固定M8螺丝即可。

GS-1006 simple sequence of opeations and description 送料机夹式送料机
1 Material line set
Place materials in holder, manual valve On (No1) grip material, make material bottom align with the mold or slightly higher than 0-01mm

2 feeding time setting
When power press is 355 °, Feeding: Feeding to 0 (in the direction of press operation, turn the pulley, the deputy ruler has moved to align the scale 0)

3 Adjust material thickness
A Feeder of the setting: Manual Valve Off (No2), Counterclockwise rotate indicator ring of mterial thickness to “0” 夹式送料机的用途
B manual adjustments:
(1) Move the seat at the top position (0 °), manual valve On (No1), turn 005mm in counterclockwise and fixed it
(2) bracket at top position (180 °) and do not relax, manual valve On (No1), turn 005mm in counterclockwise and fixed it
4 Feeding pitch adjustment: 送料机夹式送料机
A Press Time: 90 ° (feed end)
B Loosen the M16 nut with T-wrench to adjust to the setting length, and fix M16 nut Note: If the feeding pitch is unstable, please pay attention to adjustable screw loose or not

5 Loose settings: 送料机夹式送料机
A time: when finish feeding, follow pin in the material
B Loosen the screws M8 cam, adjust the line so it is on relax, fixation M8 screws

型式
Feed Model

制造号码
Serial No:

材料宽度
Material width

放松角度
Pilot release
可调整Adjustable

材料厚度
Material thickness

送料机